Search found 60 matches

by mdillmann
02 Nov 2017, 09:03
Forum: General questions
Topic: Valves not closing after a few days
Replies: 114
Views: 7212

Re: Valves not closing after a few days

HI Brieuc, currently 3 out of my 4 valves do not close for sure occasionally. For the 4th I need to examine the behavior a bit longer before exchanging them. BUT: if that is really a mechanichal failure of 3 out of 4 devices .... @Fabio: I did apply WD40 on the valve-pin (of the radiator) yesterday ...
by mdillmann
28 Oct 2017, 10:40
Forum: General questions
Topic: Re-Install valve / retract pin ?
Replies: 0
Views: 172

Re-Install valve / retract pin ?

Hi, as I have some problems with some valves not closing fully, I thought of unmounting and re-mounting them again just to make sure they fit correctly. Problem: if I unmount a closed valve (pin fully extended) and re-mount I might apply too much peasure while re-fastening. So question: is there a m...
by mdillmann
26 Oct 2017, 18:18
Forum: General questions
Topic: Valves not closing after a few days
Replies: 114
Views: 7212

Re: Valves not closing after a few days

Going back a few days, the valves did close (temperature decreased), but it fact they do not seem to open fully :twisted: because it takes 4 hrs to heat up the room 1 degree. The behavior then was quite different to the graph of today. Today (see graph in my previous post) it heated up quite ok, but...
by mdillmann
26 Oct 2017, 17:57
Forum: General questions
Topic: Valves not closing after a few days
Replies: 114
Views: 7212

Re: Valves not closing after a few days

Hi, currently the valve in the bathroom is not closing fully. One can see in the screenshot that officially no heating occurs, but the temp stays up because the radiator is heating :roll: I would really like to know what is causing this. As calibration fixes this, this means the valve thinks it is c...
by mdillmann
16 Oct 2017, 20:48
Forum: General questions
Topic: Smart valve is still working
Replies: 8
Views: 591

Re: Smart valve is still working

Yep,
it would really help what resolved that issue because I could face a similar one.

Thanks,
-Markus
by mdillmann
16 Oct 2017, 20:42
Forum: General questions
Topic: Valves not closing after a few days
Replies: 114
Views: 7212

Re: Valves not closing after a few days

Hi Zib, I think (better hope) that the smart valves react differently if attached to a thermostat or just the relay (as in my case). In the Thermostat-Forum it was mentioned that it is normal, that valves do not close fully because the Thermostat switched off the heat source: https://forum.netatmo.c...
by mdillmann
15 Oct 2017, 18:31
Forum: General questions
Topic: Valves not closing after a few days
Replies: 114
Views: 7212

Valves not closing after a few days

Hi, I noticed that the valves do not close completely after a certain amount of time. Running a calibrate seems to fix it temporarily, but after a few days the radiators are slightly warm even if the web/app show no heating at all happened the last hours. Can this be fixed by adding the additional s...
by mdillmann
15 Oct 2017, 18:23
Forum: General questions
Topic: [Feature request] Temp-Offset/Correction per valve
Replies: 0
Views: 227

[Feature request] Temp-Offset/Correction per valve

Hi, using only relay and valves I can adjust room temperature using "offset" in the app or web. I have large living-room with two radiators and valves. I need to be able to calibrate/offset the temperature of each valve independently instead of only the room. The radiators in the living-room are loc...
by mdillmann
15 Oct 2017, 13:58
Forum: General questions
Topic: Request: Per-Room Scheduling
Replies: 11
Views: 1063

Re: Request: Per-Room Scheduling

+1

Go to advanced search