Hello everyone,
I have a brand new gas boiler: Vulcano Lifestar Connect and I can't figure out if the netatmo thermostat will work or not on it.
These are the pictures from the electronic wiring of the boiler:
Do you think it will work?
Thank you very much!
Wiring to Vulcano Lifestar Connect
Wiring to Vulcano Lifestar Connect
- Attachments
-
- FullSizeRender.jpeg (2.26 MiB) Viewed 896 times
Re: Wiring to Vulcano Lifestar Connect
Should work.
Black and Grey wires of the Netatmo Relais to the blue terminals (polarity not important, bridge wire has to be removed).
Brown and Black wired need to be added to the power source.
This boiler also has a BUS connector and may support the OpenTherm standard. In that case you could also purchase the Smart Modulating Thermostat.
But you need to share the exact model of your boiler for that.
Black and Grey wires of the Netatmo Relais to the blue terminals (polarity not important, bridge wire has to be removed).
Brown and Black wired need to be added to the power source.
This boiler also has a BUS connector and may support the OpenTherm standard. In that case you could also purchase the Smart Modulating Thermostat.
But you need to share the exact model of your boiler for that.
Home: Weather Station (V3 + Rain & Wind Gauge, 3 additional Indoor Modules, Shield), Valves Starter Pack + 7 Valves, Video Doorbell
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Re: Wiring to Vulcano Lifestar Connect
No mentioning of OpenTherm, I would go with the analog Netatmo Thermostat
Home: Weather Station (V3 + Rain & Wind Gauge, 3 additional Indoor Modules, Shield), Valves Starter Pack + 7 Valves, Video Doorbell
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Re: Wiring to Vulcano Lifestar Connect
Alright! Is there any advantage to use the smart modulation one?
Thank you
Thank you
Re: Wiring to Vulcano Lifestar Connect
You can control different functions of your boiler and get data feedback.
But the boiler has to support the OpenTherm standard to be compatible and I wasn‘t able to confirm that with yours.
You could post in the Smart Modulating Thermostat section of the forum or contact Netatmo support if you have questions about this.
But the boiler has to support the OpenTherm standard to be compatible and I wasn‘t able to confirm that with yours.
You could post in the Smart Modulating Thermostat section of the forum or contact Netatmo support if you have questions about this.
Home: Weather Station (V3 + Rain & Wind Gauge, 3 additional Indoor Modules, Shield), Valves Starter Pack + 7 Valves, Video Doorbell
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Re: Wiring to Vulcano Lifestar Connect
I have the same board.. the problem is that i cant remove the brown and black from the board to put the 4 wires (2 from Netatmo e 2 from Boiler), so, can i use an external power source and add the Brown and Black wires? thanksGEORGzer wrote: ↑22 Nov 2021, 16:20 Should work.
Black and Grey wires of the Netatmo Relais to the blue terminals (polarity not important, bridge wire has to be removed).
Brown and Black wired need to be added to the power source.
This boiler also has a BUS connector and may support the OpenTherm standard. In that case you could also purchase the Smart Modulating Thermostat.
But you need to share the exact model of your boiler for that.
Re: Wiring to Vulcano Lifestar Connect
You can use an external source, or mount a power-plug.
But it has to be the brown and blue wires from the Netatmo Relais, not brown and black.
You can also use terminals to „split“ the boiler‘s power supply wires.
But it has to be the brown and blue wires from the Netatmo Relais, not brown and black.
You can also use terminals to „split“ the boiler‘s power supply wires.
Home: Weather Station (V3 + Rain & Wind Gauge, 3 additional Indoor Modules, Shield), Valves Starter Pack + 7 Valves, Video Doorbell
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Re: Wiring to Vulcano Lifestar Connect
Hi.. you're right.. black and blue. the "split" its also a good idea. i'll try it today and let u know. thanks for your help.
Re: Wiring to Vulcano Lifestar Connect
No, BROWN and BLUE
Home: Weather Station (V3 + Rain & Wind Gauge, 3 additional Indoor Modules, Shield), Valves Starter Pack + 7 Valves, Video Doorbell
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee