After issues with Temperature readings of Netatmo valves (the room was much colder than the readings on the valves) I found a solution for controlling Netatmo valves from healthy home coach. In order to achieve this I used an app called Controller and did some automations due to limited Home app functions.
1. You have to create a new automation then add start event - value of characteristic set to any - and use temperature sensor of coach
2. Add contition - value of characteristic - select coach temperature sensor - set to desired temperature through value of characteristic and then set comparison operator to less or equal.
Also If you want you can set timespan as an additional contition to maintain your program.
3. Select scene. In my case I Used the 4 valves equipped this room and set then to a high temprature.
You can also set a new automation to a lower temperature when the desired temperature is reached
So my automation looks like this
Integration between healthy home Coach temperature sensor and valves via homekit
Integration between healthy home Coach temperature sensor and valves via homekit
- Attachments
-
- IMG_3585.jpg (88.72 KiB) Viewed 7759 times
-
- IMG_3584.jpg (80.55 KiB) Viewed 7759 times
Re: Integration between healthy home Coach temperature sensor and valves via homekit
And these are the readings from energy app and home coach coach app at the same timespan with automation running.
- Attachments
-
- IMG_3587.jpg (59.63 KiB) Viewed 7759 times
-
- IMG_3586.jpg (102.38 KiB) Viewed 7759 times
Re: Integration between healthy home Coach temperature sensor and valves via homekit
Well done sir
For non-homekit-users: something similar can be achieved with the weather station using IFTTT, since both products support this platform as well. However the Healthy Home Coach does not.
If there was a way to „correct valve temperature readings“ like this, all our problems would go away.
For non-homekit-users: something similar can be achieved with the weather station using IFTTT, since both products support this platform as well. However the Healthy Home Coach does not.
If there was a way to „correct valve temperature readings“ like this, all our problems would go away.
Home: Weather Station (V3 + Rain & Wind Gauge, 3 additional Indoor Modules, Shield), Valves Starter Pack + 7 Valves, Video Doorbell
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Office: Thermostat (V2), Healthy Home Coach, Smoke Alarm, 2 2in1 Sensors
Not a Netatmo employee
Re: Integration between healthy home Coach temperature sensor and valves via homekit
If you have weather station v3 which HomeKit is supported I believe you can do it with the same way. V2 users can use homebridge on raspberry to add weather station in homekit and then follow the same procedure.
Re: Integration between healthy home Coach temperature sensor and valves via homekit
StepByStep for a newbie once again .. please. I‘ve many netatmo Valves, the coach and many Indoor Modules from netatmo, too.
Re: Integration between healthy home Coach temperature sensor and valves via homekit
cannot yet realize it. my english is probably too bad.
Re: Integration between healthy home Coach temperature sensor and valves via homekit
Hello ..
Have now got the following: But what about the heating plans in the netatmo app? What did you set ther?? Because now only the manual boost is set when heating is activated.
Timo
Have now got the following: But what about the heating plans in the netatmo app? What did you set ther?? Because now only the manual boost is set when heating is activated.
Timo
Re: Integration between healthy home Coach temperature sensor and valves via homekit
Have you test it? Is it working properly?
You can set a lower standard temperature in this room (e.g. 17C) in the Energy app and then create new automations in Controller app for your desired timespans.
Re: Integration between healthy home Coach temperature sensor and valves via homekit
I used the “absent” setting in the app and kept the two routines from above in homekit. But as I said, these only run briefly in "boost mode" and go off again. so doesn't really work. or something is wrong with my settings.