Suggestion: room based heating, not thermostat heating

Locked
Eurolfy
Posts: 4
Joined: 06 Nov 2017, 09:16

Re: Suggestion: room based heating, not thermostat heating

Post by Eurolfy » 07 Nov 2017, 19:14

Hello again Brieuc,
below my last recap:

OK relay 70:ee:50:1e:35:da firmware 159
OK thermostat 04:00:00:1e:4b:d8 firmware 64
OK the valve 09:00:00:00:23:49 firmware 47
OK the valve 09:00:00:00:50:8b firmware 47
OK the valve 09:00:00:00:60:f7 firmware 47
OK the valve 09:00:00:00:61:4a firmware 47
OK the valve 09:00:00:00:68:60 firmware 47

NOT YET UPDATED
the valve 09:00:00:00:3c:d2 firmware 43
the valve 09:00:00:00:68:db firmware 43 (this is the valve for which I ask also a warranty because is broken and doesn't work properly, doesn't connect since two months)

Thanks again for your great job.
Alfonso

Mariuss
Posts: 19
Joined: 24 Sep 2017, 21:17

Re: Suggestion: room based heating, not thermostat heating

Post by Mariuss » 07 Nov 2017, 22:41

Is it just me or do others have problems too? Valves temperatures are all over the place, jumping up and down without heating or opening windows. Boiler is running, rooms are heated over 24 degrees C while app thinks&shows no heating. I switched back to the ECO mode, the new COMFORT was unusable... I’ll post screenshots when I’m at my computer (writing this on my tablet).

Dynablaster76
Posts: 3
Joined: 08 Nov 2017, 00:44

Re: Suggestion: room based heating, not thermostat heating

Post by Dynablaster76 » 08 Nov 2017, 01:06

Hi Brieuc,
Could i also have the update?
These are mine:
Thermostat 04:00:00:1e:53:08 fw ver 59
Relay 70:ee:50:1e:83:d0 fw ver 150
Valve 09:00:00:00:86:55 fw ver 41

Thanks
Paolo

ognyan
Posts: 10
Joined: 24 Oct 2017, 08:28

Re: Suggestion: room based heating, not thermostat heating

Post by ognyan » 08 Nov 2017, 07:44

Now all of my equipment is updated.
Here is my feedback, after I have switched to Comfort.

Full scenario:
1. At 6:32 I manually increased the temperature in the living room to 22 degrees from the iOS app.
2. At 6:35 I switched to Comfort from the web app and canceled the manual setting from the iOS app.
3. As you can see from the screenshot only one of the bedrooms needs heating following the schedule. According to the app only this room is heated. In fact the living room is also heated even if the app shows the opposite. You can see on the diagram that the room temperature is increasing from 20.5 to is 21.5 at the end. When I touch the radiator in the living room it is hot, but according to the application it is not working. The kid's bedroom where the thermostat is located is not working. This is not NORMAL.
* I don't know if it is possible that my manual setting for the living room is still set even if it is not shown by the web app or the iOS app. I will do some more tests.
2. In my opinion the firmware update process is confusing. The full update takes around 48 hours. I have similar products that use wireless signal to communicate between them (like Sonos for example) and the firmware update is fast and the process is visible for the user.

Best Regards.
Attachments
Screen Shot 2017-11-08 at 8.11.10.png
Last edited by ognyan on 08 Nov 2017, 08:16, edited 1 time in total.

whnagel
Posts: 93
Joined: 24 Nov 2014, 14:00

Re: Suggestion: room based heating, not thermostat heating

Post by whnagel » 08 Nov 2017, 08:10

@ognyan did you calibrate the valves after firmware upgrade?

ognyan
Posts: 10
Joined: 24 Oct 2017, 08:28

Re: Suggestion: room based heating, not thermostat heating

Post by ognyan » 08 Nov 2017, 08:14

No.

cagliostro
Posts: 10
Joined: 07 Nov 2017, 10:09

Re: Suggestion: room based heating, not thermostat heating

Post by cagliostro » 08 Nov 2017, 09:05

Good morning
I received the firmware update for the relay 159, but the valves and the thermostat did not respond. can you help me, do you have advice to give?
thank you all

whnagel
Posts: 93
Joined: 24 Nov 2014, 14:00

Re: Suggestion: room based heating, not thermostat heating

Post by whnagel » 08 Nov 2017, 09:11

@cagliostro you have to wait update behind the Relais lasts up to 8 hours or sometimes more (see thermostat firmware updates at the very bottom)

cagliostro
Posts: 10
Joined: 07 Nov 2017, 10:09

Re: Suggestion: room based heating, not thermostat heating

Post by cagliostro » 08 Nov 2017, 09:21

thanks @whnagel
the relay update I received 24 hours ago, I'll follow your advice and look.
thanks so much

mariano
Posts: 2
Joined: 07 Nov 2017, 10:20

Re: Suggestion: room based heating, not thermostat heating

Post by mariano » 08 Nov 2017, 11:28

Good morning Brieuc.

Could i have the update please?

my relay: 70:ee:50:1e:8b:1a Firmware:150
thermostat: j1e8230 FW 59 Firmware:59

Valves Firmware:41
o007681
o002079
o008778

Thank you

Locked

Return to “General questions”